Sheet metal is the most quotable product in the whole mechanical supply chain and the easiest one to quote badly. A laser cutter runs at a fixed cost per hour, a press brake runs at another, and powder coating is priced by the square metre. On paper, two shops with the same machines should land within a few percent. They never do. When we see a 40% spread on a simple enclosure, it is almost never the hourly rate — it is that one shop read the drawing as a different job than the other.
That gap shows up on the buyer's side as either a lost deposit or a surprise. We have watched a 12 mm base plate get quoted at 6 mm prices because the thickness callout was buried in a note, and we have seen a "no tooling cost" bending price turn into a USD 800 punch and die at the end of the month. This is the set of variables that decide what you are really buying.
Thickness is a price step, not a linear scale
Buyers assume 8 mm sheet costs a third more than 6 mm. In practice, cost moves in steps, because the machine, the consumables and the handling all change when you cross a gauge boundary. A 1.5 mm chassis panel cuts fast on a 3 kW fibre laser with nitrogen assist. Take the same outline to 12 mm and you are likely on oxygen assist at a quarter of the cutting speed, with slower pierces and more dross to grind. On stainless, the jump from 3 mm to 6 mm can double the cutting time on identical geometry.
So the first thing we do when a quote looks wrong is check the material, not the labour. Confirm plate thickness and grade in the drawing title block, not only on the assembly drawing, and confirm the standard being quoted — a 304 stainless in metric and an imperial 11 gauge are not the same part. If the RFQ says "mild steel" and the fabricator has to guess, they will guess toward the cheaper step and the price will look great until the prototype arrives.
Bend count and tolerance: where the real cost hides
Bending is the quiet driver of sheet metal cost. Each bend needs a cycle, a back-gauge position and a handling move; each different bend angle on a different material thickness usually means a tooling change. A part with four bends on one station is cheap. The same part with eight bends in three angles and two radii is not twice the work — it is closer to three times, because setup stops being trivial.
Tolerance compounds the problem. A general ±0.5 mm on a formed panel is standard and essentially free. Tightening formed dimensions to ±0.2 mm forces the shop onto a different tooling strategy — gauging off formed features, slower check cycles, sometimes a dedicated fixture — and can add 20–35% to the bend operation alone. If the tolerance is not functionally necessary, it is the most expensive decoration on the drawing. Mark the two or three dimensions that genuinely matter as critical and let the rest float to the general tolerance block.
| Lever | Cheap end | Expensive end | Typical cost impact |
|---|---|---|---|
| Material / thickness | 1.5–3 mm mild steel | 8–12 mm stainless, or aluminium | 2–4× on cutting time alone |
| Bend count / angles | 2–4 bends, one angle | 8+ bends, mixed angles and radii | +50–150% on forming |
| Formed tolerance | General ±0.5 mm | ±0.2 mm with critical features | +20–35% on forming |
| Hardware (PEM, weld studs) | None, or few standard inserts | Mixed brands, tight positions | +3–8% part cost, plus insertion time |
| Finish | Mill finish, or zinc plating | Powder coat + masked areas, brushed SS | +15–40% of total part cost |
| Volume | 1–10 pieces | 500+ pieces | Unit price falls 40–60% |
The volume question: make ten, or make five hundred
Sheet metal has two very different cost curves, and buyers routinely send a drawing to the wrong kind of shop. Under roughly fifty pieces, you are buying machine time — every part carries its share of programming, nesting, first-off inspection and setup. Past a few hundred pieces, the picture flips: hard tooling, dedicated fixtures and progressive operations start to make sense, laser versus stamping becomes a real decision, and unit price can fall by half.
What does not fall is the one-off cost. Programming, first-article inspection and any custom punch or die stay on the invoice regardless of quantity, which is why a 10-piece quote at USD 42 a piece and a 500-piece quote at USD 12 are both "correct" for the same drawing. When you send an RFQ, always ask for two or three quantity tiers in one response — 10, 100 and 500. It costs the fabricator twenty minutes and gives you the real shape of the cost curve, which is the number you need for pricing your own product.
Watch this line item: "Standard hardware" is not a spec. If your drawing calls for PEM-type inserts and the quote says only "hardware included", you can receive pressed studs with a different tooth pattern that will not hold torque in the field. Name the insert brand and part number, or approve a named alternate list, the way you would with a connector.
Finishing: the step that gets forgotten and then rushed
Finishing is where projects slip. Powder coating needs a pretreatment line, a cure oven and colour acceptance — and if the shop outsources it, you have added a third party between you and your delivery date with no visibility. Two things go wrong repeatedly. First, masked areas: threaded holes, mating faces, datum surfaces and grounding points must be masked before coating, or the coating builds 60–100 µm and your fastener no longer seats. Call out masked zones on the drawing, not in the email thread.
Second, the coating specification itself. "Black powder coat" is not a requirement. You want the standard (typically the applicable ISO or Qualicoat-class specification), a target dry-film thickness with tolerance — 60–80 µm is a common architectural range, thinner on precision assemblies — the colour reference system (RAL number, not a photo), and the salt-spray hours if the part goes outdoors. For anything galvanised or zinc-plated, specify the coating weight in g/m² and whether the part is passivated; on threaded hardware, add the torque-tension and hydrogen embrittlement requirements for high-strength fasteners. These are not exotic asks; they are what a competent finishing house already works to, and putting them in writing is what makes them happen.
How to send a sheet metal RFQ that gets comparable quotes
Most of the spread between quotes is buyer-side. If the package you send is ambiguous, each shop resolves the ambiguity in whichever direction suits its shop floor. The package that produces comparable numbers is short and boring: a dimensioned DXF or STEP for every flat part with a clean outer profile and no duplicate or overlapping entities, a PDF drawing with material grade and standard, thickness, general and critical tolerances, bend notes with radius and direction, hardware callouts with part numbers, finish specification with colour reference, and a quantity table with at least three tiers.
Two more habits pay off. Ask what is excluded — many quotes are ex-works with no crating, and on heavy welded frames crating and sea-freight protection can add real money to a machine frame that has to arrive square. And ask for the process description: which machine cuts, which press brakes, who does the finishing, and whether finishing is in-house. A shop that outsources both finishing and welding is a trading desk with a laser in the corner, which is fine — as long as you know it before you build the schedule around them.
None of this makes sheet metal hard. It is a mature, well-understood process with plenty of competent shops across China and Southeast Asia, and a good one will tell you that your tolerance band is unnecessary or that your bend sequence will not close. The buyers who get burned are the ones who sent a drawing and negotiated only on price. Fix the five levers above, ask for the quantity curve, and the 40% spread collapses into a number you can actually plan a product around.